STEP PLUMBING GUIDE FOR INSTALLING A BATHTUB

Step Plumbing Guide for Installing a Bathtub

Step Plumbing Guide for Installing a Bathtub

Blog Article

Instant Quote

How do you really feel with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


Installing A Bathtub
Setting up a bathtub isn't specifically brain surgery, however it does need strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily accessible, the job can relocate easily; if you have to open a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old tub and embeded in the new one. See to it you have qualified on your own for the job and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to think about utilizing one before you start. Chances are you might require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already acquired a new tub and also don't need to alter the plan of your previous supply of water pipelines.
Your devices and also product list need to comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome as a result of the limited gain access to that is frequently the case.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. As soon as the taps have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
    Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next, place the faucet in the mounting hole in the bath/basin making certain that the washers are in place between the tap and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The previous type must be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Installing the Tub


    Using both wooden boards under its feet, put the bath tub in the needed position. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
    The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also readjusting the feet on the bathtub up until the level reviews degree.
    To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
    Switch on the water supply and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill the tub and additionally check the overflow outlet and also the normal outlet for leaks.
    Finally, deal with the bath paneling as described in the supplier's instruction manual. Tiling and securing around the bath tub needs to wait till the tub has been used at least when as this will resolve it right into its final position.

    Preparing for the Setup


    First of all, the sustaining frame provided with the bath should be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
    Fit the flexible tap ports to the bottom of both taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the provided washers.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final setting.

    Tiling Around the Tub


    In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split a stiff seal, creating the water to permeate the wall in between the bath and the tiling, leading to problems with moisture and possible leaks to the ceiling below.
    You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not consider this motion prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I found that piece on Tools You Need to Install a New Bathtub while looking around the search engines. Those who liked our page if you please don't forget to pass it around. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .


    Drain issues? Reach out!

    Report this page